Top 17 Best Mosfet for 3D Printers in 2022

Finding the right mosfet for 3d printer has become a challenging task because there are so many choices out there. This is why we’ve compiled a list of the best mosfet for 3d printers so that you can compare them and choose the right one for your needs.

All the mosfet for 3d printers featured on this page are independently chosen. When you make any purchase through links on this site, we may earn a small affiliate commission at no extra cost to you.

Followings are the best-selling mosfet for 3d printers on Amazon:

Last update on 2022-10-05 / Affiliate links / Images from Amazon Product Advertising API

While checking out the mosfet for 3d printers, you may also be interested in our collection of the best motherboard for 3d printers.

Best Mosfet for 3D Printers

In the following section, we’ve compiled the most popular mosfet for 3d printers available today. To make your choice easier, we’ve listed some of the key features of each of these mosfet for 3d printers.

1
Highlighted Features:
  • 1.Power is connected to the power supply, pay attention to positive and negative.
  • 2.Hotbed connected to the hot bed heating line, pay attention to positive and negative.
  • 3.Digital control signals can be connected to Gnd and D8 directly.
  • 4.Connect the control signal from the Ramps1.4 or MKS motherboard MOS tube to Bed.
  • 5.The two sets of control signals can only be connected to one group.
2
Highlighted Features:
  • WELL MADE- New material with superior quality stainless, High-grade Aluminum block for best connectivity and long life.
  • HIGH TRANSMISSION - With this addon module to your 3D printer motherboard you can lead the maximum current up to 25A.
  • MULTIFUNCTION - Completely solve the hot bed power is too large and load current problems,and can well protect the connectors on the controller board from overheating.
  • MEET YOUR NEEDS -Widely used for common 3D printer models,extruder and other open 3D printer motherboards.such as Anet A8, etc.
  • WARNING - For use on some devices (for example,Anet A8),you need to make sure the power supply is set to 110 volts instead of the default 220 volts.If the voltage is too high, the product will get super hot, even charred!! Don't touch it lightly.
3
Highlighted Features:
  • HIGH QUALITY:High quality large heat sink ensures a better heat dissipation
  • EXCELLENT PERFORMANCE:The MOS tube performance is excellent, nominal maximum current is 280A
  • STABLE LONG-TERM WORK:Maximum current can be up to 30A for stable long-term work
  • NOTE:Can be directly controlled by Ramp1.4 and MKS series motherboard hot bed output signal
  • CONTROL:Can be controlled by digital signal of 5V to 24V
4
Highlighted Features:
  • Function and Use: control hot bed, print head heating, compact appearance, compact design, more powerful heat dissipation, to solve the problem of excessive heat bed power, current load problem;
  • Extra large heat sink, the maximum current can be up to 30A or more, can use digital signal of 5-24v to control;
  • This module under normal cooling, measured I (Max) = 30A can Stable long-term work during use, so we suggest the current should not exceed 30A.
  • Connect the control signal of Ramps1.4 or MKS Mosfet to bed, can use hot bed output signal of Ramp1.4 and MKS series to control;
  • Package includes: 2Pcs Mini Mosfet with line
5
Highlighted Features:
  • ☆FUNCTION - Small size, compact design, more powerful heat dissipation, completely solve the problem of excessive heat bed power and load current, and can well protect the connector on the control board from overheating.
  • ☆WELL MADE - Heat Bed Mosfet made with high quality stainless steel, high grade aluminum blocks for optimal connectivity and long life.
  • ☆HIGH TRANSMISSION - With this addon module to your 3D printer motherboard you can lead the maximum current up to 25A. Under the premise of normal heat dissipation, this module can work steadily under the condition of I(Max)=25A, the current must not exceed 25A while the process working.
  • ☆MEET YOUR NEEDS - Widely used in common 3D printer models, extruders, Chitu motherboards and other open frame 3D printer motherboards. Such as Anet A8 and so on.
  • ☆NOTICE - For use on some devices (for example,Anet A8), you need to make sure the power supply is set to 110 volts instead of the default 220 volts. If the voltage is too high, the product will get super hot, even charred! Don't touch it lightly!
6
Highlighted Features:
  • A general add-on heated bed power expansion module for 3D printer
  • Completely solve the hot bed power is too large and the load current issue. It can work with the Anet A8
  • With this addon module to your 3D printer motherboard you can lead the maximum current up to 15A
  • Under the premise of normal heat dissipation, this module can work steadily under the condition of I(Max)=15A. Don't exceed 15A during the process.)
  • If you intend to use heated bed with your 3D printer that uses a 12V power supply, then this module is recommended, else it may cause excessive current during times which may burn the connectors on the controller board, According to the thermal power of the bed, please choose the appropriate power supply, with sufficient margin. If it is large power heated, we suggest 24V power supply, under the same power requirements, current is less than 12 v
7
Highlighted Features:
  • CURRENT OVERLOAD - With this add on module to your 3D printer motherboard you can lead the maximum current up to 30A.
  • UNIQUE DESIGN: With unique snowflake heatsink design, it has a great cooling effect. The heat bed power module can be used in both Lerdge motherboard and other 3D printer motherboards.
  • WELL MADE - The best connection is made of new materials and high quality stainless steel and the high grade aluminum blocks, which give longer product life.
  • APPLICATION: This high power module is a general add-on heated bed power expansion module for 3D printer. It can work with the Anet A8.
  • SAFETY - New terminal insulation cover to prevent leakage, to avoid electric shock, so use more safer.
8
Highlighted Features:
  • CURRENT OVERLOAD - With this add on module to your 3D printer motherboard you can lead the maximum current up to 30A.
  • UNIQUE DESIGN: With unique snowflake heatsink design, it has a great cooling effect. The heat bed power module can be used in both Lerdge motherboard and other 3D printer motherboards.
  • WELL MADE - The best connection is made of new materials and high quality stainless steel and the high grade aluminum blocks, which give longer product life.
  • APPLICATION: This high power module is a general add-on heated bed power expansion module for 3D printer. It can work with the Anet A8.
  • SAFETY - New terminal insulation cover to prevent leakage, to avoid electric shock, so use more safer.
9
Highlighted Features:
  • This high power module is a general add-on heated bed power expansion module for 3D printer.
  • Made of high quality material, it is durable and long lasting use.
  • Equipped with large heatsink, the maximum electric current is above 30A.
  • You can use Ramp1.4 or heatbed of MKS mainboard directly to output signal control.
  • - It can be used 5-24V number signal control.
10
Highlighted Features:
  • Currently work with the Anet A8
  • Completely solve the hot bed power is too large and the load current issue
  • General add-on heated bed power expansion module
  • With this addon module to your 3D printer motherboard you can lead the maximum current up to 25A
  • Under the premise of normal cooling, it work stable under I(Max)=25A, the current must not exceed 25A while the process working
11
Highlighted Features:
  • Voltage: 12V to 24V; Max Current: Over 30A
  • Maximum power of the heated bed: Over 360W (12V) or 720W (24V)
  • Make sure that the cables from the controller board to hotbed can withstand high current
  • Thermal paste has been applied between the heat sink and MOSFET chip. The fan will further cool down the chip, so the MOSFET controller can work better under high current than other controllers.
  • We recommend using a 24V power supply when using a heat bed with high current
12
Highlighted Features:
  • External high current mosfet module is a solution for power a large heatbed without blow up the control board of your 3D printer.
  • Working voltage:DC 12-24V ;Working current:typical 30A up to 40A with coolingfan; Control pin compatible with both aux pin and bed mosfet output
  • It can be controlled by any aux pins from control board so you can save a mosfet output to doing other things(need to change the heater pin in the firmware)
  • Please mind the anode and cathode of the connectors; Please insure the wire of your circuits is big enough for handle such amonut of current; Do not tin the ends of the wire; Preferably,use bootlace ferrules on the end of the wires; Please make sure the screws of the mosfet module terminals are tighten up to minimize the contact resistance otherwise the terminals will melt under lager current.
  • Each module will doing a load test before delivery; Superior performance of MOSFET(60V/230A R(ds)2.2mΩ); Large heat sink 57A terminals; Can handle up to 40A with cooling fan
13
Highlighted Features:
  • This module is provided by official Makerbase (MKS), Each one will be done functional test By manufacturer.
  • Superior performance of MOSFET (Max 280A). Can use digital signal of 5-24v to control .
  • Extra large heat sink , the maximum current can be up to 30A or more.Voltage 12V or 24V,
  • Package:1piece MKS MOSFET module.
  • Cable is NOT included, please must be sure cable can withstand high current before getting the cable for this module.
14
Highlighted Features:
  • Currently work with the Anet A8
  • General add-on heated bed power expansion module
  • With this addon module to your 3D printer motherboard you can lead the maximum current up to 25A
  • Under the premise of normal cooling, it work stable under I(Max)=25A, the current must not exceed 25A while the process working
  • Completely solve the hot bed power is too large and the load current issue
15
Highlighted Features:
  • Each one has done functional test
  • Superior performance of MOSFET (Max 280A)
  • Extra large heat sink , the maximum current can be up to 30A or more
  • Can use hot bed output signal of Ramp1.4 and MKS series to control
  • Can use digital signal of 5-24v to control
16
Highlighted Features:
  • Heat Bed Power Module - This high power module is a general add-on heated bed power expansion module for 3D printer. It can work with the Anet A8.
  • Unique Design - The unique design of the snowflake radiator makes the cooling function more powerful, to solve the large hot bed power and current load problem.
  • 25A Maximum Current - Under the normal heat dissipation, the module can be stable long-term work when measured I (Max) = 25A. When using the module, the current should not exceed 25A.
  • Good Protection - When using heated bed 3D printer for 12V power supply which may cause excessive current during times, with this module, it can well protect the connectors on the controller board from burning.
  • Power Supply / Operating Voltage: 12V-50V (12-24VDC recommended),Max Current: 25A (Enhance heat dissipation) safe for prolonged times. ensure active cooling of the heatsink.
Sale17
Highlighted Features:
  • 2560 and Ramps 1.4 are integrated in the board, which avoids the problem of complicated connectors and malfunctioning. Support a variety of stepper drivers such as A4988, DRV8825, TMC2100, available to change the stepper drivers and motors as users like.
  • Reserve external driver signal, available to connect external high-current driver to drive the 57 and 86 stepper motors. Use high-quality MOSFET, better cooling effect and more stable. Use specific power chip, support 12V-24V power input, and resolve t.
  • Stable and reliable filter circuit greatly reduces interference and avoids crashes as possible in the process of printing. Use CH340 serial port chip, more easily install the drive than 16U2.
  • Support 24V input, the heated bed current can be reduced to 1/4 at the same system power which effectively resolves the problem that the MOSFET of heated bed heats. Run Marlin firmware, the configuration is completely same as Ramps 1.4.
  • Support Ramps 1.4, 2004LCD,12864LCD, TFT28 and TFT32. X-axis, Y-axis and Z-axis with different color terminal controls the stepper motors and endstops, which is convenient to wire.

Last update on 2022-10-05 / Affiliate links / Images from Amazon Product Advertising API

So, these are all of the top-rated mosfet for 3d printers currently available on the market. We recommend reading all the features of each of the above-mentioned mosfet for 3d printers before making a purchase decision. This will help you identify the right product for your requirement.

If you like the above listing, you may also like our reviews of the top motors for 3d printers.

Guide for Choosing the Best Mosfet For 3D Printer

If you are ever in the market for buying mosfet for 3d printer, you probably know how difficult it is to find the best one for the money. You may get confused thinking about:

  1. Who makes the best quality mosfet for 3d printer in the industry?
  2. Which one is the best mosfet for 3d printer for the money?
  3. How to choose the right mosfet for 3d printer on the market?

When it comes to choosing the right mosfet for 3d printer among a wide variety of options, you should consider some factors. Those factors may include quality, performance, features, value, etc. Without considering those factors you may end up buying a poor quality mosfet for 3d printer that will not provide you with the best value for your money.

Before investing in mosfet for 3d printer, you should find the answer to the following questions:

  • Do you really need to buy mosfet for 3d printer?
  • How much value you are expecting from the mosfet for 3d printer?
  • What factors do you believe should be considered when buying mosfet for 3d printer?

Don’t forget to check our listing of the best multi extruder 3d printers.

To help you make an informed decision, here we are going to discuss the factors that you should consider when shopping for mosfet for 3d printer whether online or from any retail store.

Product Quality

Product quality should be the most important factor to consider when shopping for mosfet for 3d printer. You are going to use this product for a long time. So, you should consider the quality of the mosfet for 3d printer and make sure it will fit your requirement.

Features

The mosfet for 3d printer comes with a lot of features and functionalities. In this article, we’ve mentioned the features of each of these mosfet for 3d printers so that you can choose the right one for your needs. You should read all the features of the mosfet for 3d printer before making a decision.

Read Our Recommendations for The Best Xerox Laser Printers.

Price

You can get an array of mosfet for 3d printers, from the cheapest to the most expensive. The mosfet for 3d printer that costs more is usually made from better materials and will last longer than a cheaper one. But if you want to be able to purchase a new mosfet for 3d printer every few months, you may want to consider the budget-friendly options.

Reviews and Ratings

Finally, the customer reviews and ratings should be considered when buying mosfet for 3d printer. Good customer reviews and ratings indicate that the mosfet for 3d printer is going to perform well whereas bad ratings and negative reviews indicate that people already have faced problems using that particular product. Read our reviews of multi filament 3d printers.

Final Verdict

We hope you enjoyed our listing of the best mosfet for 3d printers. As you can see, there are still so many alternatives to choose from. So, it’s better to check out each of these items carefully and pick the right mosfet for 3d printer that сan satisfies all your requirements.

Leave a Comment